q-in-q tunneling configuration





I have to configure q-in-q tunneling along with mc-lag. Can anyone help me with the configuration part of q-in-q with respect to 2 customers. And also let me know what is the purpose of q-in-q over dot1q. Service provider switch configured to process Q-in-Q for traffic coming in on Ethernet 7/1. A Layer 2 protocol tunnel is enabled for STP BPDUs.l2protocol tunnel stp switch(config-if) no shutdown switch(config-if) exit switch( config) exit switch. Verifying the Q-in-Q Configuration. The official names of these configurations are an 802.1q Tunnel and an EtherChannel over an 802.1 q Tunnel.Lets start with the basic 802.1q Tunnel (aka The Tube or more commonly QinQ tunneling). The first item of note is that in order for this to work, you will need to change the system mtu to 1504 By using 802.1Q tunneling the layer 2 domain of a customer can be extended across multiple sites. A Q-in-Q frame can be identified by the Ethertype fieldIn order to support frames larger than 1500 bytes on Ethernet ports we can use the command system mtu in global configuration mode. When configuring Q-in-Q tunneling the ports connected directly to the customer switch are configured with the command switchport trunk encapsulation dot1q. The customer ports are configured as per normal and require no extra configuration. The Juniper Networks Junos operating system implementation of Q-in-Q tunneling supports the IEEE 802.1ad standard. Note: This task uses a Junos OS release that supports the Enhanced Layer 2 Software (ELS) configuration style. Any tunnel port in a tunnel VLAN is a tunnel entry and exit point.

An 802.1 Q tunnel can have as many tunnel ports as are needed to connect customer switches.Chapter 17 Configuring IEEE 802.1Q Tunneling. 802.1Q Tunneling Configuration Guidelines and Restrictions. The following configuration on the C-VLAN interface ge-0/0/1 enables Q-in -Q tunneling and maps packets from C-VLANs 100 through 200 to logical interface 10, which is in turn associated with S-VLAN v10. Layer 2 Switching Configuration. Q-in-Q Basic Port Configuration. Q-in- Q tunneling allows service providers on Ethernet access networks to extend a Layer 2 Ethernet connection between two customer sites. SCENARIO PURPOSE .

To extend customer VLAN 50 across customer WAN environment from Site A (CPE1) to Site B (CPE2). Below us the diagram for reference where customer has 2 locations Site A (CPE1) and Site B (CPE2) which need to communicate over service provider network Layer-2 tunneling is different from Q-in-Q tunneling but it can be run along with Q-in-Q or even independently without Q-in-Q.Q-in-Q Tunneling and L2TP Configuration. Below is the Diagram we will utilize to configure a very simple Q-in-Q sample network. Cisco 802.1Q Tunneling aka Q-in-Q. Q-in-Q is a feature often used by service provider as a layer 2 VPN. The configuration is very simple, put a 802.1Q tag on interface that it receives from customer and on interface that it out to customer other side. Dot1Q tunnel or q-in-q tunneling is a technique generally used by service providers to extend customers VLANs to different locations.In this blogtorial, we will take a look at a very simple topology with easy to follow configurations. Today i will discuss how to Configuring Q-in-Q vlan tunnels in cisco switch. At first login your Switch then apply bellow command.VLAN Mapping Cisco Switch Configuration Cisco Switch VLAN Security Cisco Switch Port Security Configuration. Q-in-Q tunneling enables service providers on Ethernet access networks to segregate or bundle customer traffic into different VLANs by adding another layer of 802.1Q tags. this article provides q in q in juniper EX3300. Understanding Q-in-Q Tunneling. Note: This topic applies to Junos OS switches with support for the Enhanced Layer 2 Software (ELS) configuration style. 18 QinQ Configuration. This chapter describes how to configure 802.1Q-in -802.1Q (QinQ).QinQ tunneling is configured on PE1 and PE2 in the following way to implement communication within each department and isolate the two departments 802.1Q tunneling (aka Q-in-Q) is a technique often used by Metro Ethernet providers as a layer 2 VPN for customers. 802.1Q (or dot1 q) tunneling is pretty simplethe provider will put a 802.1Q tag on all theEnough talklets take a look at the configuration. Heres what the router configs look like In this article, we are going to talk about QinQ tunneling configuration between Juniper MX10 and Cisco ASR1001, its basically Junos and IOS. Before going to the main part, let start with some introduction so that you understand a little bit about QinQ. Understanding QinQ Tunneling. Information About Q-in-Q Tunnels. A Q-in-Q VLAN tunnel enables a service provider to segregate the traffic of different customers in their.Configuration Examples for Q-in-Q and Layer 2 Protocol Tunneling, page 9-16. Cisco Q in Q Tunneling CCIE Blog » Blog Archive » 802.1Q Tunnelling (QinQ) 802.1 Q Tunnelling (QinQ) In this lab we are going to join 2 sites of a customer network using QinQ through our Service Provider (SP).Cisco IPSec Tunnel Configuration. IEEE 802.1Q Tunnel Ports in a Service-Provider Network. Customer A VLANs 1 to 100.Catalyst 3560 Switch Software Configuration Guide. OL-8553-05. Chapter 16 Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling. Configuration: Configuring 802.1Q tunneling is pretty straightforward, all that is required is to configure the CE-PE connections as 802.1Q trunks on the CE sideStep 2 - Configure the CE ports connecting to the PE devices as trunks: "switchport mode trunk" in interface configuration mode. 802.1Q Tunneling (Q-in-Q) Configuration Example. Detail Configuration for Cisco Q-in-Q in Cisco Devices. Introduction to Q-in-Q Principle. 802.1Q tunneling (aka Q-in-Q) is a technique often used by Metro Ethernet providers as a layer 2 VPN for customers. For point-2-point 802.1q tunnels, an easy solution is to use EoMPLS tunnels on the central routers/switches in order to allow the double-taggedCEF is needed too, but its enabled by default and cannot be disabled on 6500s/7600s. Configuration. These are the relevant configurations 4 Configuring 802.1Q Tunneling Chapter 14 Configuring 802.1Q Tunneling Default 802.1 Q Tunneling Configuration, page Q Tunneling Configuration Guidelines, page Q Tunneling andStep 11 copy running-config startup-config (Optional) Save your entries in the configuration file. May 22, 2017 This article provides an example configuration of Q-in-Q tunneling for receiving both untagged and tagged traffic using a customer scenario with the following requirements: Accept any type of frames (tagged/untagged) from clients. Cisco Systems 3750-X инструкция : Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling 12.2.2 802.1Q Tunneling Configuration Guide. In configuring the 802.1Q, it is required to confirm that the connection with the 802.1 Q tunnel is an asymmetric link, with a VLAN dedicated for each tunnel. Q-in-Q Configuration To display Q-in-Q tunnel and Layer 2 protocol tunneling configuration information, perform one of the following tasks: Command clear l2protocol tunnel counters [interface if-range] Purpose Clears all the statistics counters. switchport mode dot1q-tunnel. This configuration will transport and preserve all the vlan information of the customer. Here in example, As fa0/13 is a trunk port, CP1 will transmit all the tagged frames on it. 802.1Q tunneling expands VLAN space by using a VLAN-in-VLAN hierarchy and tagging the tagged packets, and the maximal VLAN number can reach 4096 This example shows how to configure a switchport to basic dot1q-tunnel port. You can use show the configuration on the switchport. However, this is very limiting, both in that it removes the customers flexibility to choose their own VLAN numbers, and there may not be enough VLAN numbers (we can only use a maximum of 4,094 or so) available on large networks.802.1Q Tunnel Configuration. VLANs configured for a VLAN-transparent service and a VLAN-specific service follow the VLAN-specific service configuration. If you need to configure 802.1Q tunneling, configure this VLAN-transparent service in the normal manner, see the " Configuring IEEE 802.1Q Tunneling" section. 802.1Q Tunnel Configuration.Howie (guest) January 21, 2015 at 2:20 p.m. UTC. For the folks asking above about maximum nesting, its worth knowing that q-in-q tunneling is NOT done by encapsulation like a VPN. Tail-f NCS Layer 2 Q-in-Q Tunnels - Продолжительность: 9:26 Stefan Wallin 699 просмотров.Learn how to create a dot1q trunk (802.1q) configuration on Cisco IOS from ccieadvisor.com - Продолжительность: 4:10 ccieadvisor 12 032 просмотра. (1) Configuration on Provider A Configure VLAN 100 as the default VLAN of GigabitEthernet ge-1/1/1, and enable the Q-in-Q tunneling internal mode on GigabitEthernet ge-1/1/1. A 802.1q tunnel (also known as QinQ), is used on metro-ethernet networks to obtain L2 (802.1 q) adjacency between customer devices.In the example above CDP and VTP were enabled so SW3 and SW4 became CDP adjacent and can exchange VLAN configuration using VPT. With this configuration, traffic passing into swp1 with VLAN 100 egresses out of swp2 with VLAN 37. The original VLAN (100) is lost however.Hi Bryan, QinQ (or the standardized 802.1ad) is not supported in 2.5 or 3.0 currently. It should be coming in 3.1 or 3.2, not sure specifically, but it is Q-in-Q tunneling expands the VLAN space in the service provider network.Note - See Packets Might Be Dropped When Using Q-in-Q Interop in Certain Configurations (6989048) for information about special requirements for third-party switches. When Dot1q tunneling is configured,a layer 2 protocol tunneling can also be configured,a layer2 protocol tuneling allows layer2 PDUs(Protocol Data Units) to beQ-in-Q Tunneling and L2TP Configuration. Below is the Diagram we will utilize to configure a very simple Q-in-Q sample network. Cisco Nexus 7000 Series NX-OS Interfaces Configuration Guide.Chapter 9 Configuring Q-in-Q VLAN Tunnels Information About Layer 2 Protocol Tunneling Se n d d o c u m e n t c o m m e n t s t o n ex u s 7 k . Note Layer 2 protocol tunneling works by tunneling BPDUs in software. configure terminal. Enter global configuration mode.copy running-config startup-config. (Optional) Save your entries in the configuration file. Verifications: sh dot1q tunneling sh l2protocol-tunneling. Chapter 9 Configuring Q-in-Q VLAN Tunnels. Send document comments to nexus7k-docfeedbackcisco.com. Note Q-in-Q is supported on port channels and vPC.Q-in-Q tunnels and Layer 2 tunneling have the following configuration guidelines and limitations When I put the configuration on the tunnel ports, the switch prompted me to change my MTU to 1504 reload the switch.Use one dot1q tunnel interface/VLAN per customer. Be sure to tag your customers native VLAN traffic into the QinQ VLAN (I forgot to do that in my lab). S3400 Web Configuration Manual. Port: The number of the port that is configured with port monitoring in the switch Enable port monitor: Whether to enable the port-level monitoring.Q-in-Q (Vlan dot1q tunnel) Configuration. Configuration prerequisites. Enable STP in the customer networks before configuring BPDU tunneling for STP. BPDU tunneling configuration examples. IMPORTANT: By default, Ethernet, VLAN, and aggregate interfaces are in DOWN state. A QFX5100 allows for dot1q-tunneling, or Q-in-Q. If you ever configured dot1 q-tunneling on an EX-switch, this configuration differs a lot from what you may be used to. Cisco Nexus 6000 Series NX-OS Interfaces Configuration Guide, Release 7.

x OL-30916-01 1 Configuring Q-in-Q VLAN Tunnels Q-in-Q Tunneling The 802.1Q tunneling expands the VLAN space by using a VLAN-in-VLAN hierarchy and tagging the tagged packets. Q Tunneling Q in Q Configuration Example. Q inQ Enables the Service Provider to carry and transport the customer VLANs across the provider switches When the Service Provider carries VLANs from multiple As discussed here the Cisco Q Interface Signaling QSIG tunneling over IP feature